Hello All. My friend gave me an Azden SGM-X awhile back for my Pansonic PV-DV851 (a camcorder with no manual audio control).

I have tried to use the mic, but it is ridiculously hot. If there is a quiet computer/air flow in a "silent" room the sound of it will be overpowering, and voices from even a few feet away are picked up as very loud, (nearly clipping).

Is there any kind of in-line attenuator or limiter with 3.5mm mini-jack IO's that I could use, and would a solution like that even work? here are the specs right out of the manuals...

Camera -
Audio Input Level {Line} - 316 mV, 10kohm or more (I think this is referring to the component audio input)
Mic Input - Mic sensitivity -50dB (0dB = 1V/Pa, 1Khz)

Microphone -
Impedance: 1.5k Ohms @ 1KHz
Max. SPL Input Level: 103dB
Signal to Noise Ratio: 65dB
Dynamic Range: 78dB
Battery Type: LR-44 - USE ALKALINE BATTERY
Battery Current: 0.5 mA

I tried to research this first and could only find optical and XLR in-line attenuators/limiters. I'd like to be able to use the mic, but if I had to buy something like a Beachtek, I might as well buy a better mic too, and that is a whole new bag of worms.

Any suggestions or ideas about the subject are welcome, and I thank all of you ahead of time for reading this and (possibly) helping me out.

One idea, if you're handy, is make your own attentuator with some 1/8" connectors and a few Radio Shack resistors.

http://www.dplay.com/book/pgs2e/pads.pdf

Just ordered a 10dB 200ohm inline XLR for £26.00 inc taxes . . I had this from Sennhieser and the suppliers of the same. http://www.canford.de/commerce/productdetails.aspx?productid=20-910

Seems like good value. Tested and components and my time and frustration . . Oh, and I can then add another inline for 20dB . . . simple and quick.

Grazie

I'm not really handy enough to build my own attenuator, and I'm looking for something like that XLR in-line attenuator, just with mini plugs. Of course I could get the XLR one and a couple of XLR to mini adapters, but at that cost I might as well look for a used Beachtek style device. Thanks for the advice though guys, anybody else?

Oh! You know those little volume control dials they put in-line with some walkman headphones? Could I find and use something like that with a mic, or would that introduce too much noise to the system? Anybody know of these things being sold as separate in-line accessories?

Bad Audio will only . .er . . sound quieter. You will have "hot" quiet audio. Having a volume control will only make that which is horrid - quieter.

Grazie

I don't think you'll find a solution as cheap and convenient as we hope for, Jesse.

BTW, are you sure there's no mic attenuation option buried in the cam's menus? There is in my GL2.

Yes, I've used it often on my XM2. If you go with the onboard mic, it's sweet, it works well. Try high register girls gospel choir, in full flow? If I plug on my Senni66 it is still too hot. I've been advised to use this inline attenuator by a Senni Engineer here in the UK - so, Guys that's what I'm gonna do - only for massively big . . er, hotness.

Seeyah!

Grazie

So what's the difference between having an attenuator in between the mic and camera vs. a volume control in between the mic and camera. I'm sure this is a ridiculous question, but I really don't get it, so please don't berate me if you answer! I kind of "got" Graham's response, but want to know the why. If the signal from the mic (which is battery powered if that makes a difference), get lowered by a volume knob before it hits the cam, how could it still clip?

Here's a link to an attenuator cable with 1/8" connectors--

http://www.core-sound.com/attenuator-cables.html

Thanks a lot Jay. Just what I was looking for (I think). I'm going to try this. They have a 30 day return policy if deosn't work, so that's a good deal!

It's not a ridiculous question, and no one berates anyone around here. You're right, your volume control idea would work in an unbalanced line as an attenuator, and when adjusted to equal the dB reduction of any other attenuator it would prevent clipping just as well. As you suspected in your earlier post, it's likely to be noisey because of the slider contact plus the fact that the resistive material used wasn't selected for this application.

Thanks Fred. I was just joking about getting berated =).

So you're saying if the mic is hot, but not automatically clipping, the in-line volume control ($15) would be better to try first before the mini-jack 20dB attenuator ($40), or are you saying that I'd probably need both?

Well, I got the $10 volume control and put it in-line, between the mic and the cam, and it worked wonderfully, except...even with the voulme knob at it's loudest the audio is about 6dB too quiet. I guess I could just raise it in post...

I have Audio-Technica AT8202 Attenuators. They have a 10, 20, 30 switch AND are phantom voltage compatible. Some attenuators do not work with phantom voltage, so be aware. I think they are around $40 and I got mine from one of our sponsors (B&H).

I appreciate the repsonse, but as earlier posts said, I'm not looking for an XLR solution.

<<<-- Originally posted by Jesse Bekas : Well, I got the $10 volume control and put it in-line, between the mic and the cam, and it worked wonderfully, except...even with the voulme knob at it's loudest the audio is about 6dB too quiet. I guess I could just raise it in post... -->>>

Unfortunately, when you do, you'll also bring up 6dB of system noise. You got halfway there, but you still need to get it "righter."

Regards,

Ty Ford